IML - IML-RESI PowerDrill ®

Yes, the drill can inspect when it is in freezing weather. However, decay can also freeze and show a higher resistance than above freezing. However, you can still detect decay with the change in the resistance if the decay is frozen.

The standard inspection drills are water resistant, not waterproof. You will want to treat the drill as you would your smart phone of other electronic devices that are water resistant.

Many customers use the drill for pole inspections by conducting three drillings on the pole. First to determine the diameter for the WoodInspector software, second drilling into the base of the pole at an angle of about 30 degrees and then another drilling perpendicular to this at the base of the pole. This way the inspections are calculating the data below ground where there is a higher chance of decay. The WoodInspector software provides instant results of the drilling by determining if the pole is a pass, marginal or fail.

With the WoodInspector- software you will get a direct condition assessment of the wooden pole right after performing the measurements. Here, individually specified rot and cavity limit values of the timber branch to be inspected are included as criteria for the evaluation. To view more details visit the WoodInspector page.

Yes, you can take the information from PD/F Tools or WoodInspector and utilize it in your GIS or other related software.

All additional modules can also be retrofitted to your device. Either at our service centre or conveniently at your home with an activation code generated by us.

A test disc is worn out when the needle is assessed with the needle status “Worn out, replace needle!”. Wear marks/indentations are safe indications for a worn out test disc.

The test disk may be worn out. The test disc is a replaceable disc in the front adapter. If the needle is pulled through the test disc during the needle test, the needle is rated as bad. It is possible that the test disc is worn out. For this purpose, we offer exchangeable test discs and the appropriate tool.

This activates the automatic needle retraction. This is a protective mechanism that counteracts excessive bending of the needle. It is set to 5 cm by default. The retraction length can be adjusted under Control Panel > Automatic Needle Retraction.

! We recommend a retraction length between 5 – 10cm. If the retraction length is too long, the needle and the telescope can be damaged when the needle breaks!

– Active Bluetooth mode means the pairing is started by the drill. You must create a new connection in order to pair. To do this, you must find the computer on the side of the device and pair it.
– Passive Bluetooth mode means that the computer or the handheld initialises the pairing. To do this, you must search for and pair the Resi via the computer’s own Bluetooth manager. (This pairing variant is the most common pairing variant).

The Bluetooth must be turned on. And the correct mode must be selected for your device pairing. If there is still no connection, try out to update your Bluetooth driver. Instructions can be found under Instruction manuals & software downloads in the “Bluetooth Drivers” section”.

Control Panel > General > Rotate Display: NO

Now the rotation mode of the display is switched off.

A drill chuck should be replaced when irregular resistance is felt when turning by hand, or the rear “offset value” is over 400. (see illustration)

The needle wear depends on several factors. You will find an illustration of this in the maintenance instructions (page 14) enclosed with your machine.

Press the device against the object to be tested. When the safety button is pressed, press the red and black button simultaneously. The tilt indicator in the display now lights up green and the REL symbol appears in the upper right corner. The current unit orientation has thus been selected as reference plane 0°. To switch off the real time mode, return the unit to its original position and press the safety switch and the two buttons again, or switch the unit off and on again.

Press the red button for a long time > Tilt compensation: ON

Now the tilt compensation is switched on. If the drilling depth preselection is switched on, the machine will select the actual drilling depth according to the set diameter/radius and the current tilt angle. ! The TLT add-on module is required for this!

Remove the 45° adapter and detach the front adapter from the unit Now move the feed unit forward !SLOWLY! Guide the telescope by hand to avoid jamming the drilling needle in the telescope. When you reach the front end position, pull the telescope out of the unit. Now bend the broken drilling needle by 90° and hold it with the pliers for the manual needle change. Remove the needle. Insert the telescope in the front end position and then move back to insert a new needle.

If any problems or uncertainties arise during disassembly or reassembly, please contact our service department. We will be happy to assist you.

Your unit synchronises itself with the system time of your computer each time it is connected. The current time set in the computer is always used.

The individual feed rates can be assigned individually via the System controls > Feed rate menu. By deleting the individual values, individual feed rates can also be deleted completely from the “Quick selection”.

It is possible to choose between several drilling needle speeds in the Advanced View, equal to the feed rate

System Controls > Drilling Needle Speed > Mode: Advanced

The different steps can also be individually assigned different speeds.

There is the possibility of data recovery. This restores all data still present on the Resi. Provided they have not yet been overwritten. Control Panel > Data Recovery > YES

Make sure that the drilling depth preselection is switched off. If the number 2.0 appears on the display, the drilling depth preselection is set to 20mm. To deactivate it, press and hold the red button while the machine is switched on. Now the Drilling settings menu appears and you can switch the drilling depth preselection to OFF status.

Check whether the 45° adapter is correctly mounted and whether the symbol for the safety switch lights up in the display when pressed.

Press the red or black button instead of the navigation button for a longer period of time. If the device does not switch on again, contact the service. Switching on via the navigation button can be activated/deactivated in Control Panel > General > Navi Button Switch On Device.

The standard scope of delivery includes 2 batteries (18 V, 5.0 Ah). These can be fully charged in approx. 30 minutes with the quick charger.